Battle of the Light Bulbs: Pt1

3DFS > Articles  > Battle of the Light Bulbs: Pt1

Battle of the Light Bulbs: Pt1

In today’s world customers are offered an array of lighting choices.  Several light bulb producers promise tempting energy savings, but beyond the higher cost of bulbs, are you getting anything beyond the promised energy savings?

Lighting products can be broken down into three categories:  incandescent, halogen, compact fluorescent (CFL), and LED.  We are going to look at just the 60W or equivalent (on lumen output ≈800) and standard fixtures of each type for simplicity.

battle-tests

 

*Overall luminous efficacy of a glass halogen is 16 lm/W and 24 lm/W for a quartz halogen, so we will use the average at (16+24)/2= 20.

From what we can observe above, it seems that the best choice for an efficient light bulb would be the LED because it provides over quadruple the lumens per watt in comparison to the incandescent bulb.  Most people would stop here and make the decision to choose a CFL or an LED; however, we decided to look deeper to see how far the rabbit hole goes.

 

The Basics:

Incandescent bulbs have been around since 1810, using a filament that’s heated to the point where it glows.  The glowing filament produces the bulb’s light and a good amount of heat.

 

Halogen bulbs operate on the same principle as incandescent bulbs.  The evaporated tungsten mostly deposits onto the inner surface of the bulb.  The halogen sets up a reversible chemical reaction cycle with the tungsten evaporated from the filament.  The halogen cycle keeps the bulb clean, and the light output remains almost constant throughout life of the bulb.  The halogen bulb operates at significantly hotter temperatures than the incandescent bulbs.

 

Compact fluorescent bulbs (CFL) have an electric current and a high voltage flow between electrodes at each end of a tube containing gases.  The reaction produces ultraviolet (UV) light and heat.  The UV light is transformed into visible light when it strikes a phosphor coating on the inside of the bulb.  The bulbs contain 3-5mg of mercury per bulb.

 

Light Emitting Diode (LED) bulbs use a small electrical current passing through a semiconductor material to illuminate the tiny light sources called LEDs.  The heat produced is absorbed into a heat sink, keeping the bulbs cool to the touch.

 

Light Bulbs from the electrical network standpoint:

Scouring research papers that have measured the THD and PF of light bulbs was a difficult task because many of the papers were industry sponsored, so our data was sourced from independent researchers around the world.  As a side note, the industry sponsored research papers’ results varied, typically favoring either CFLS or LEDs, while independent research studies were rather consistent, reinforcing our confidence in the data.

 

electric-bulb
 

Looking at the bulbs from the electrical perspective paints a very different picture.  LED and CFS are the electrical quality offenders, but what does this mean?

 

CFLs cause additional line losses due to low power factor.  These heat losses affect the life of machines and cables; therefore, the failure rate is higher. These losses also generate additional running costs over a period of time.

 

LED lamps prove to be a better option because they generate less heat loss and less harmonic distortion with greater power factor.  Hence these are more reliable, both in terms economics and power quality effects.

 

However if your facility is equipped with a 3DFS power controller, the full effectiveness of CFL and LED can be realized:

 

correction

 

Having clean power turns electrical quality offenders such as CFL and LED bulbs to near ideal electrical quality and efficiency! With 3DFS the full potential for CFLs and LED light bulbs is realized. The customer will get all the savings and longer life, without the electrical problems.

Stay tuned as we plan on release more detailed studies, reports, and articles for the lighting industry.

11 Comments
  • Sandra
    Reply
    Posted at ,

    Great Article !

    Wow had no idea that power quality has a rather huge impact on things. I researched the topic for a good part of the day today and you guys are right on the money.

    I am forwarding your contact information to the purchasing manager for our facility.

    Thank you again.

  • Mark Oroth
    Reply
    Posted at ,

    This makes quite a bit of scene, However not for most people as 20 light-bulbs will have little or no effect on anything no matter how bad the power quality is!

    However when you take into the consideration that a facility with say 5,000 lightbulbs this is critically important especially taking into an account that changing the lighbulbs is a pain in the ass… so if 3dfs can extend lifespan this would be a huge savings.

  • Holley huish
    Reply
    Posted at ,

    Cant wait for part 2 !

  • Materace
    Reply
    Posted at ,

    Keep this going please, great job!

  • Karl Abron
    Reply
    Posted at ,

    Oh my goodness! Awesome article dude! Thanks,
    However I am going through troubles with your RSS. I don’t know the
    reason why I am unable to subscribe to it. Is there anybody else having the same RSS problems?

    Anyone that knows the solution can you kindly respond? Thanks!!

  • Jaden Zanie
    Reply
    Posted at ,

    very interesting, Just saw the how the lightbulbs work video as well seems that we are innovating lighting however the power grid needs innovation as well

  • Issac Maez
    Reply
    Posted at ,

    You absolutely have fantastic articles.

  • Luigi F
    Reply
    Posted at ,

    I simply want to say I am just new to blogs and absolutely loved you’re web-site. Many thanks for revealing your website page.

  • Eimon
    Reply
    Posted at ,

    Oh my goodness! Impressive article dude! Many thanks

  • masaż
    Reply
    Posted at ,

    Thanks for finally writing about >Battle of the Light Bulbs:
    Pt1 | I Liked it!

  • Carol
    Reply
    Posted at ,

    You share interesting things here. I think that your blog can go viral easily, but you must give it initial boost – I will retweet it hopefully it will give it a push

Post a Comment

Comment
Name
Email
Website